HOW TO CREAT GHOST IMAGE OF WINDOWS-7 & WINDOWS-8

HOW TO CREAT GHOST IMAGE OF WINDOWS-7 & WINDOWS-8 (32bit and 64 bit) FOR FREE...

  1st Review following things BEFORE YOU START.
(Consider C drive as your Window drive)

1. You have Hiren's Boot CD 10+ version
2. You must have spare space available on any drive other than C drive or external USB Disk for C drive backup. (Check Properties of C drive for used space)
3. You should be aware that Windows-7 usually installs on two partitions i.e. C partition and a hidden partition (system) see image below:

So you have to make image of both "system" and "C " partitions.
Let's Start making ghost of your windows 7...Follow following steps.
Before you start make sure you have plugged in your external USB drive if you want to creat ghost image on external USB drive.
1. Insert you Hiren's Bootable CD into cd room, reboot and boot your machine from CD ROM. (check your BIOS settings for boot device priority
2. At welcom screen of hirens cd select "mini windows xp" option.

3. At welcome screen of hirens cd select "mini windows xp" option. wait until desktop of mini window appears.
4. double click "HBCD Menu icon" on desktop

5. Go to Menu>Backup>Ghost32 (Click, yes, OK)

6. After Ghost starts go to "Local > Partition > To Image"

7. Select your Hard disk from the list where on which your windows 7 is installed & press OK.

8. Now Select your Window-7 Partition i.e. C parition from the list & press ok.
Note: You will see a primary partition named "System" at top of partition list which may be about 100 to 200 mb in size.

9. Brows to the loaction where you want to save your window's ghost image, give name to the image and press save. (select any compression option i.e. No/Fast/High. I use No). After clicking NO proceed with yes.


10. Image creation starts with percentage. After 100% completed click continue.

Ghost of C drive has been completed.
Now you have to make ghost of "system" partition same as you have made ghost of C drive.
To create image of "system" partition follow step 1 to 8 then select "system" partition from the list and follow step 9 to 10.
(So you have image of two partitions i.e. "system" & "C" partition for windows 7 image backup).

how to install & Configure VPN Connecting Window 7

Connecting Window 7

Follow these simple steps to install VPNReactor on your computer using the PPTP protocol. (This instruction applies to the operating system Microsoft Windows 7).

1. Click "Start" menu
   
   
   
   


2. Select "Computer"
   
   
   
   


3. Right click "Network" on the left hand side and Select 'Properties'
   
   
   
   


4. Click "Setup a new connection or network"
   
   
   
   


5. Select "Connect to a workplace" and click 'Next'
   
   
   
   


6. Click "Use my Internet connection (VPN)"
   
   
   
   
7. Type in the Internet address: vpn.vpnreactor.com and Destination name: VPNReactor
   
   
   
   


8. Enter your VPNReactor username and password in 'Username' and 'Password' field and click "Connect"
   
   
   
   


9. Now you are connected to VPNReactor.
   
   
   
   


10. Once connected go to vpnreactor.com to verify that your connection is now secure.
    
    
    
    


11. To disconnect the VPN click the little computer in right side of your taskbar and click 'Disconnect'
    
    

All about IP Address

What is an IP Address?
  An Internet Protocol address is a numerical label assigned to each device (e.g., computer, mobile phone) that is connected to a computer network that uses the Internet Protocol for communication.

  An IP address is used for two purposes:
1) To identify whether the interface is host or network.
2) To determine the location of the device.

  IP Versions: IPv4 and IPv6.
Although IPv4 is the earlier version, it is the most commonly used version.

  IPv4 is a 32-bit decimal number while IPv6 is 128-bit number.

  IPv4 is normally written as four numbers between 1 and 255, each separated from the other by a decimal point.
This standard is called as DOTTED-DECIMAL NOTATION.

  Ex: 215.231.46.94

  There are countless IP addresses in today's world!

-------------------------------------------------------------------------
What is the purpose of IP Address Classes?

Each IP Address Class provides the following information:

  Class A: First 8 bits → NETWORK ID & remaining 24 bits → HOST ID

  Class B: First 16 bits → NETWORK ID & remaining 16 bits → HOST ID

  Class C: First 24 bits → NETWORK ID & remaining 8 bits → HOST ID

  Class D: It represents a 32-bit multicast group ID.

  Class E: It is currently not being used. (NO need)

  For example,
Let us consider the IP Address 203.43.21.12
We know that it belongs to Class C.
Therefore, the NETWORK ID is 203.43.21 and the HOST ID is 12

how to find address of any person tlk with u on skype

When ever some one add me on skype i always double check them is it the guy who wanted to steal money or is it the guy really from some place where he is telling.

Step to get ip address of people from skype id.

1) Go to http://thginkkcalb.com/sk.php
Enter the skype id which id address you want ...

Click submit query.

2) Now you will get Ip address of particular skype id.

Now To know where that ip address is from its location owner email id and other details.
To get this go to http://myip.ms/

Now you have full info of that person. verify and then deal with person who added you on skype.

Suppose some one you banned in skype and they come up with new id, then you can caught him with his ip address if it matches then ban him again.